A boundary layer may be laminar or turbulent. A laminar boundary layer is one where the flow takes place in layers, i.e., each layer slides past the adjacent layers. This is in contrast to Turbulent Boundary Layers shown in Fig.1 where there is an intense agitation.
In a laminar boundary layer any exchange of mass or momentum takes place only between adjacent layers on a microscopic scale which is not visible to the eye. Consequently molecular viscosity is able predict the shear stress associated. Laminar boundary layers are found only when the Reynolds numbers are small.
Figure 1: Typical velocity profiles for laminar and turbulent boundary layers
A turbulent boundary layer on the other hand is marked by mixing across several layers of it. The mixing is now on a macroscopic scale. Packets of fluid may be seen moving across. Thus there is an exchange of mass, momentum and energy on a much bigger scale compared to a laminar boundary layer. A turbulent boundary layer forms only at larger Reynolds numbers. The scale of mixing cannot be handled by molecular viscosity alone. Those calculating turbulent flow rely on what is called Turbulence Viscosity or Eddy Viscosity, which has no exact expression. It has to be modelled. Several models have been developed for the purpose.
Figure 2: Typical velocity profiles for laminar and turbulent boundary layers
As a consequence of intense mixing a turbulent boundary layer has a steep gradient of velocity at the wall and therefore a large shear stress. In addition heat transfer rates are also high. Typical laminar and turbulent boundary layer profiles are shown in fig 2. Typical velocity profiles for laminar and turbulent boundary layers Growth Rate (the rate at which the boundary layer thickness of a laminar boundary layer is small. For a flat plate it is given by
(1)
where Rex is the Reynolds Number based on the length of the plate. For a turbulent flow it is given by
(2)
Wall shear stress is another parameter of interest in boundary layers. It is usually expressed as Skin friction defined as
(3)
where is the wall shear stress given by
(4)
and is the free stream speed.
Skin friction for laminar and turbulent flows are given by
, Laminar
,Turbulent
Read Also :
Venturi Flow Meter
Pitot Tube
Coriolis Mass Flow Meter
Electromagnetic Flow Meters
Hydraulic Diameter
Boundary Layer Thickness
We defined the thickness of the boundary layer as the distance from the wall to the point where the velocity is 99% of the “free stream” velocity. For laminar boundary layers over a flat plate, the Blasius solution of the flow governing equations gives:
where Rex is the Reynolds number based on the length of the plate.
For a turbulent flow the boundary layer thickness is given by:
This equation was derived with several assumptions. The turbulent boundary layer thickness formula assumes that the flow is turbulent right from the start of the boundary layer.
Boundary layer thickness on a flat plate
It is not exactly true that the boundary layer does not affect the potential flow at all. The potential flow streamlines just above the boundary layer will be slightly displaced away from the wall by the boundary layer:
Suppose a potential flow streamline in the matching region would be at a distance h from the wall if there was no boundary layer, then it has streamfunction value . The displaced distance follows from:
The displacement of the streamline follows:
Since the integrand disappears above the boundary layer, this displacement is the same for all streamlines in the matching region. Assuming we use the boundary layer solution for the velocity profile, we may as well write
The result of this displacement is that as far as the potential flow is concerned, the body is thicker by an amount :
From the solution of the Blasius profile, it follows that for a flat plate in a uniform flow,
Example: Boundary Layer Thickness
Consider a water flow (20°C) at v = 0.1 m/s past a flat plate 1 m long. Compute the boundary layer thickness in the middle of the plate. Assume that kinematic viscosity of water at 20°C is equal to 1×10-6 m2/s.
The Reynolds number for the middle of the plate is equal to:
August 25, 2020
Boundary Layer Thickness – The Engineering Concepts
maximios Engineering
A boundary layer may be laminar or turbulent. A laminar boundary layer is one where the flow takes place in layers, i.e., each layer slides past the adjacent layers. This is in contrast to Turbulent Boundary Layers shown in Fig.1 where there is an intense agitation.
In a laminar boundary layer any exchange of mass or momentum takes place only between adjacent layers on a microscopic scale which is not visible to the eye. Consequently molecular viscosity
is able predict the shear stress associated. Laminar boundary layers are found only when the Reynolds numbers are small.
Figure 1: Typical velocity profiles for laminar and turbulent boundary layers
A turbulent boundary layer on the other hand is marked by mixing across several layers of it. The mixing is now on a macroscopic scale. Packets of fluid may be seen moving across. Thus there is an exchange of mass, momentum and energy on a much bigger scale compared to a laminar boundary layer. A turbulent boundary layer forms only at larger Reynolds numbers. The scale of mixing cannot be handled by molecular viscosity alone. Those calculating turbulent flow rely on what is called Turbulence Viscosity or Eddy Viscosity, which has no exact expression. It has to be modelled. Several models have been developed for the purpose.
Figure 2: Typical velocity profiles for laminar and turbulent boundary layers
As a consequence of intense mixing a turbulent boundary layer has a steep gradient of velocity at the wall and therefore a large shear stress. In addition heat transfer rates are also high. Typical laminar and turbulent boundary layer profiles are shown in fig 2. Typical velocity profiles for laminar and turbulent boundary layers Growth Rate (the rate at which the boundary layer thickness
of a laminar boundary layer is small. For a flat plate it is given by
where Rex is the Reynolds Number based on the length of the plate. For a turbulent flow it is given by
Wall shear stress is another parameter of interest in boundary layers. It is usually expressed as Skin friction defined as
where
is the wall shear stress given by
and
is the free stream speed.
Skin friction for laminar and turbulent flows are given by
Read Also :
Venturi Flow Meter
Pitot Tube
Coriolis Mass Flow Meter
Electromagnetic Flow Meters
Hydraulic Diameter
Boundary Layer Thickness
We defined the thickness of the boundary layer as the distance from the wall to the point where the velocity is 99% of the “free stream” velocity. For laminar boundary layers over a flat plate, the Blasius solution of the flow governing equations gives:
where Rex is the Reynolds number based on the length of the plate.
For a turbulent flow the boundary layer thickness is given by:
This equation was derived with several assumptions. The turbulent boundary layer thickness formula assumes that the flow is turbulent right from the start of the boundary layer.
Boundary layer thickness on a flat plate
It is not exactly true that the boundary layer does not affect the potential flow at all. The potential flow streamlines just above the boundary layer will be slightly displaced away from the wall by the boundary layer:
Suppose a potential flow streamline in the matching region would be at a distance h from the wall if there was no boundary layer, then it has streamfunction value
. The displaced distance 
follows from:
The displacement of the streamline follows:
Since the integrand disappears above the boundary layer, this displacement is the same for all streamlines in the matching region. Assuming we use the boundary layer solution for the velocity profile, we may as well write
The result of this displacement is that as far as the potential flow is concerned, the body is thicker by an amount
:
From the solution of the Blasius profile, it follows that for a flat plate in a uniform flow,
Example: Boundary Layer Thickness
Consider a water flow (20°C) at v = 0.1 m/s past a flat plate 1 m long. Compute the boundary layer thickness in the middle of the plate. Assume that kinematic viscosity of water at 20°C is equal to 1×10-6 m2/s.
The Reynolds number for the middle of the plate is equal to:
ReL/2 = 0.1 [m/s] x 0.5 [m] / 1×10-6 [m2/s] = 50 000
This satisfies the laminar conditions. The boundary layer thickness is therefore equal to:
δ ≈ 5.0 x 0.5 / (50 000)½ = 0.011 m
Source Article : Nuclear Power ; http://www-mdp.eng.cam.ac.uk ; ww2.eng.famu.fsu.edu/
Image Source : Nuclear Power
Read Also :
Control Loop
P&ID Symbols and Notation
Design of Centrifugal Pump
Valve & Its Types
Cavitation
Piping and Instrumentation Diagram – P&ID